Forum Replies Created
-
April 1, 2025 7:50 am
Step 8:
Remove the all bolts that secure the ends of the EGR cooler, pull the cooler forward, carefulyinspect and remove any clips or wiring harnesses that may be connected to the cooler, andthen remove the cooler from the vehicle.
April 1, 2025 7:41 amStep 7:
1. Disconnect the clamp of the EGR top cooling pipe.
2. Remove the PCM wiring harness from the passenger side firewall. Secure it so that it doesnot hinder installation.
April 1, 2025 7:39 amStep 6:
1.Remove the longer EGR pipe that is secured in place with five bolts. There are two bolts oneach tooth, one on the bracket. Ensure that all hardware and gaskets are retained for futureuse.2. Remove the short EGR pipe fixed with four bolts. Ensure that all hardware and gaskets areretained for future use. Pay attention to removing the probe connected to the pipeline.
April 1, 2025 7:37 amStep 5:
1. Remove the wiring harness from the top of the EGR cooler. An orange plug with a yellowlocking tab and a black plug, and connect the wiring harness from take it off the bracketPull off the vacuum line at the top of the EGR system, remove the hard plastic line from the port,and plug it with the provided rubber cover.
April 1, 2025 7:34 amStep 4:
1. Disconnect the hose connected to the exhaust gas recirculation system, and thendisconnect the two clamps connected to the T-shaped pipe at the other end.
2. The straight hook accessories provided in the installation kit.
April 1, 2025 7:31 amStep 3:
Disconnect and completely remove the twolarger coolant lines leading to the EGR cooler.
April 1, 2025 7:23 amStep 2:
Release the two clamps that connect the intake box to the manifold intake pipe joint, then pullout the three cooling pipes from the remaining intake pipe clamps and remove the remainingintake pipes.
April 1, 2025 7:11 amStep 1:
Disconnect two batteries and drain the coolant.
Remove the MAF (Mass Air Flow) sensor located on the air intake. Release the red tab tolock the plug for disassembly.
April 1, 2025 7:01 amPackage includes:
- 1 * “U”Shaped Black Coolant Tube
- 1 * Exhaust Block Off Plate
- 2 * Hose Clamps1*0-ring
- 1 * High Flow Intake Elbow
- 1 * M8x20 Hex Head Bolts
- 2 * M8 x 25 Cap Head Bolts
- 3 * M10 x 20 Hex Head Bolts
- 2 * M8x20 Cap Head Bolts
- 1 * M8 Flange Nuts
!Before installation, confirm that:
This high-performance component does not comply with the laws and regulations for highwaydriving and cannot be used on any vehicle that has been registered or certified for use onhighways. This means that the component may only be suitable for racing cars or other off-roadvehicles. lf it is installed on vehicles driving on the highway, legal issues will be borne byoneself.
March 28, 2025 2:08 amStep 2:
1. Remove the intake pipe from the filter to the plastic turbine interface.
2. Gently pry out three rubber washers and remove the bellows and filter.
March 28, 2025 2:08 amStep 1:
1. Disconnect batteries,
2. Remove the passenger side inner wheel cover to drain the engine coolant, and disconnectthe lower radiator pipe by removing the metal clip.(Note: lt is not necessary to completely pull out the pipe, just allow the coolant to flow out.)3. Loosen the hose clamps on the intake, and disconnect the MAF sensor connector.
March 28, 2025 2:08 amPackage lncludes:
- 1 *“U”Shaped Black Coolant Tube
- 1 * Exhaust Block Off Plate
- 2 * Hose Clamps
- 1*0-ring
- 1 * High Flow Intake Elbow
- 1 * M8x20 Hex Head Bolts
- 2* M8 x 25 Cap Head Bolts
- 3 *M10 x 20 Hex Head Bolts
- 2 * M8x20 Cap Head Bolts
- 1 * M8 Flange Nuts
!Before installation, confirm that:
This high -performance component does not comply with the laws and regulations for highwaydriving and cannot be used on any vehicle that has been registered or certified for use onhighways. This means that the component may only be suitable for racing cars or other off-roadvehicles. lf it is installed on vehicles driving on the highway, legal issues will be borne byoneself.
